How To Forge A Knife From Rebar Ideas

How To Forge A Knife From Rebar. 6 grinding and sharpening : A gas forge is much simpler to use.

how to forge a knife from rebar
Source :

Although forging rebar is possible, it is unnecessary if you intend to forge a knife with it. Both coal and gas can be used to forge weld rebar, however, each requires a different approach.

A Group Of Remnants Rebar Knife Tire Tool Knife And

By forging i mean that you take a piece of steel and you shape and form it in the forge and on the anvil. Each project will be detail explained by video instructions so you don’t leave with any questions.

How To Forge A Knife From Rebar

Here’s a hand forged fork made from 1/2 rebar.How is rebar as a steel for making knives and such items
as an item that holds an edge.How to forge a rebar knife part 3.How to forge a rebar knife with no power tools!

However, with chef knives, this isn’t set in stone.I do have a tutorial for that.I plan to use these for holding knife blades while i heat treat them.I will also explain whether rebar is a good material to work in the first place.

I will go over the reasons in this article, along with other basic blacksmithing tips.I would recommend using a gas forge if you are not familiar with solid fuel forge.I’m planning on making a set with a spoon, steak knife, butter knife, and maybe even a spork.If a gallows frame rig.

If it shattered going into the water, probably a good alloy but try quenching in warm vegetable oil.If you are a beginner blacksmith with limited skills and resources, use a nice long piece of rebar and you will be able to work the steel without worrying about burning your gloves or hands.If you are a beginner blacksmith with limited skills and resources, use a nice long piece of rebar and you will be able to work the steel without worrying about burning your gloves or hands.If you are a beginner, forging with coal may seem more complicated due to the fire maintenance.

If you don’t have a forge and an anvil you can still make an excellent knife.In this part of the tutorial we take the knife back out to the forge and harden/temper it.Instead of using a found lawnmower blade, use 5160, 1084, or 1070.Is rebar hard to forge?

It is called the stock removal method of knife making and you.It’ll be inconsistent, often quite brittle and difficult to rely on.Let’s start by hammering in the point at the very end.Most knives tend to have a 2:1 ratio between the length of the blade and the handle itself.

Most of them were done over 10 years ago, so finding pictures is limited.Now for a quick test on if scrap will make a decent blade, heat it up till a magnet won’t stick to it and quench it in several gallons of water.Once the point is done we want to make the curves in the handle.One was quenched in oil, the second one in water and the third one was only normalized.

Part 1 of this tutorial is located here.Press down as you move forward, then lift the file right off the knife and return to start.Raymond richard made a number of rebar knives that gave at least decent performance.Rebar can be brittle, as well, and this knife could break with too much abuse.

Rebar knives are a lot of fun to make and they have been great for practicing my forging skills.Rebar quenched in oil bent almost 90 degrees before snapping.Rinse, repeat until you have the shape you want.The first portion of this workshop will focus on heating and shaping the rebar with a hammer and anvil.

The first two thread onto the 3d very securely.The one which was quenched in water cracked almost immediately without any bending.The short answer is no, you should not forge your first knife from a lawnmower blade.The strength test is performed by hammering the rebar which is clamped by the vise.

The way i make them is to have 2 legs with closed loops at the top and 1 leg with a turn and half spiral loop at the top.Then wearing ppe try to break the quenched end:There are two curves, a small one and a large one.This inconsistency makes rebar quite difficult for newer blacksmiths trying to get some more practice.

This is a step by step tutorial that shows you how to forge a knife.This is a two step process that we do in order to change the steel into something that is very useful as a knife.This means that rebar can be unpredictable to work with.This will not be the knife you wanna take with you for a bushcraft adventure.

To forge your knife, you only need to get rebar and forge it into your knife.Today we’ll be forging a knife using a piece of 5/8″ rebar.Use a piece of steel that is about 3ft long.We want to make the small curve first.

With the basic shape of the blade done we are going to turn it around and work on the handle.You might consider various exercies in hammer control with rebar, vs.You should also put the hot rebar knife into a quench liquid;You should first dip the blade’s edge into the liquid before dropping the whole knife.

You should make sure you grind the rebar and sharpen the rebar’s blade.

Leave a Reply

Your email address will not be published. Required fields are marked *